Vivanco UR 2

Vivanco UR 2 manuál (návod)

(2)
  • UR Universal Controller
    Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: hotline@vivanco.de 1
    ( GB ) Operating Instructions -> 1
    ( D ) Bedienungsanleitung -> 2
    ( F ) Notice d'emploi -> 3
    ( E ) Instrucciones de uso ->5
    ( I ) Istruzioni per l’uso->6
    ( NL ) Gebruiksaanwijzing -> 8
    ( PL ) Instrukcja obsługi -> 9
    ( P ) Instruções de operação -> 10
    (DK) Betjeningsvejledning -> 12
    (S) Bruksanvisning -> 13
    (RUS) Руководство по эксплуатации ->14
    (GR) Οδηγίες χρήσης->16
    (TR)
    Kullanma talimatı -> 18
    (CZ)
    Návod k obsluze -> 19
    (SK) Návod na obsluhu-> 20
    (H) Kezelési utasítása -> 22
    (GB) Instructions
    Inserting the batteries
    Open the battery flap on the back of the remote
    control, press the tongue lightly downwards,
    then insert 2 alkaline AAA batteries. Check that
    the polarity markings on the batteries and in the
    battery compartment are correctly lined up
    (+=+), then close the flap carefully. – Always
    use undamaged batteries.
    Adapting to a device (e.g. TV or DVB Set
    Top Box (or SAT/Cable) etc.
    In order to control e.g. your TV or DVB you
    must adapt or set the remote control to it. There
    are two ways of doing so: direct control code
    entry or code search.
    If your UR does not understand you it blinks
    and you can then repeat the entry. Each
    understood entry is confirmed by LED blinking
    briefly.
    Direct control code entry using the enclosed
    list
    Example: setting to control a Panasonic
    television set:
    1. The enclosed list gives, for example, the
    Panasonic Code 153.
    2. To prepare code entry, briefly press the
    SET button, and then the TV-button, until the
    Powerkey lamp/LED lights constantly.
    3. Then press the number buttons (e.g. 1 5
    3) in sequence.
    4. Once the numbers have been entered the
    button lamp goes out and the remote control is
    ready to control your appliance.
    5. Finally, test the control code setting by
    trying to control your television set. If it does not
    work at all or not correctly try a different code
    from the list or the code search (see below).
    Code search
    If the brand of your appliance is not in the list or
    none of the codes given fits, we recommend a
    code search.
    Manual code search
    1. Switch on the appliance to be controlled.
    Program is running.
    2. To prepare the code search, briefly press
    the SET button and then additionally a
    appliance button, e.g. the TV or DVB button,
    until the lamp (LED) lights constantly.
    3. Then point the remote control at the
    appliance to be controlled.
    4. Briefly press the ON/OFF
    (appliance on/off) button once. The lamp (LED)
    blinks.
    5. Press the ON/OFF
    (appliance
    on/off) button repeatedly, approx. every second,
    until appliance, reacts. - If you notice the
    reaction of your appliance too late and the next
    code has already been emitted you can go back
    by pressing SET and then ON/OFF again. If
    your appliance has switched itself off you must
    switch it back on again, e.g. on the appliance or
    with the original remote control, to continue
    searching. - When your appliance reacts you
    can also try out other buttons without
    interrupting the search. If some buttons do not
    work properly, simply continue searching with
    ON/OFF.
    6. When your appliance reacts correctly,
    press the appliance button e.g. TV and end the
    search. The lamp (LED) goes out.
    - The search stops after approx. 30 seconds of
    inactivity.
    Automatic code search
    Your remote control finds the correct settings
    almost automatically in seconds:
    1. Switch on the appliance to be controlled
    so that you can watch a TV program.
    2. To start the code search, press the SET
    button, and then additionally the appliance
    button e.g. TV or DVB, for more than 3
    seconds until the Power-key lamp (LED) starts
    to blink.
    3. Then point the remote control at the
    appliance to be controlled while the remote
    control emits a different ON/OFF signal every 2
    seconds.
    4. When your appliance reacts, press any
    button, except SET, to end the search. – If you
    ended the search too late, continue to search
    using the Manual Code Search (see above).
    5. Finally, test the control code setting by
    trying to control your appliance. If it does not
    work correctly, please try the code search
    again. The code search then begins with the
    next code in the sequence. - Remember to
    switch your appliance back on again if you wish
    to continue searching.
Vivanco UR 2

Potřebujete pomoc?

Počet otázek: 0

Máte dotaz ohledně Vivanco UR 2 nebo potřebujete pomoc? Zeptejte se zde. Poskytněte jasný a komplexní popis problému a vaši otázku. Čím více podrobností uvedete ke svému problému ve vaší otázce, tím snazší bude pro ostatní majitele Vivanco UR 2 vaši otázku zodpovědět.

Zde si můžete zdarma prohlédnout příručku pro . Tato příručka patří do kategorie a byla ohodnocena lidmi průměrným hodnocením . Tato příručka je k dispozici v následujících jazycích:. Máte dotaz ohledně nebo potřebujete pomoc? Zeptejte se zde

Specifikace Vivanco UR 2

Značka Vivanco
Model UR 2
Produkt Dálkový ovladač
Jazyk Čeština, Holandský, Angličtina, Němčina, Francouzština, Španělština, Italština, Švédština, Portugalština, Dánština, Polština, Ruské, Turečtina, Slovenské, Řekyně, Maďarština
Typ souboru PDF

Související příručky produktů

Dálkový ovladač Vivanco

Často kladené otázky

Níže naleznete nejčastější dotazy, týkající se VivancoUR 2 .

Není vaše otázka uvedena v seznamu? Zeptejte se zde

Užíváme cookies, abychom vám zajistili co možná nejsnadnější použití našich webových stránek. Pokud budete nadále prohlížet naše stránky předpokládáme, že s použitím cookies souhlasíte.

Více