Honeywell RTH230B manuál (návod)

Honeywell RTH230B
9.2 · 2
PDF manuál
 · 4 stránky
Angličtina
manuálHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Zde si můžete zdarma prohlédnout příručku pro Honeywell RTH230B. Tato příručka patří do kategorie termostaty a byla ohodnocena 2 lidmi průměrným hodnocením 9.2. Tato příručka je k dispozici v následujících jazycích:Angličtina. Máte dotaz ohledně Honeywell RTH230B nebo potřebujete pomoc? Zeptejte se zde

Potřebujete pomoc?

Máte dotaz ohledně Honeywell a odpověď není v návodu?

  • Nechte si poslat aktualizace ohledně řešení
  • Získejte odpovědi na svou otázku

Otázka a odpověď

Počet otázek: 0

Honeywell RTH230B je termostat, který je navržený tak, aby vám poskytl kontrolu nad teplotou ve vašem domě. Tento termostat je vybaven programovatelným časovačem, který vám umožňuje nastavit různé teploty během dne, což vám pomáhá ušetřit energii a peníze na účtech za vytápění. RTH230B je vybaven také digitálním displejem, který vám umožňuje snadno sledovat a nastavit teplotu. Jedna z klíčových vlastností tohoto termostatu je jeho jednoduché ovládání. RTH230B má jednoduché tlačítka pro nastavení teploty a programování času. Pokud jste nový v používání termostatů, nemusíte mít obavy, protože tento termostat je nápadně snadno použitelný. Další výhodou tohoto termostatu je jeho spolehlivost a odolnost. Honeywell je renomovaná značka, která je známa svými kvalitními výrobky, a RTH230B není výjimkou. S jeho robustním a odolným provedením nebudete muset mít obavy z toho, že by se termostat snadno poškodil. Celkově vzato, Honeywell RTH230B je spolehlivý a snadno použitelný termostat, který vám umožňuje kontrolovat teplotu ve vašem domě. S programovatelným časovačem a jednoduchým ovládáním je tento termostat skvělou volbou pro každého, kdo chce ušetřit energii a zlepšit pohodlí svého domova.

Všeobecné
ZnačkaHoneywell
ModelRTH230B
Produkttermostat
JazykAngličtina
Typ souboruUživatelský manuál (PDF)

Nenašli jste v návodu odpověď na svou otázku? Odpověď na svou otázku můžete najít v častých dotazech o Honeywell RTH230B níže.

Kam je nejvhodnější umístit termostat?

Nejlepší místo pro termostat je místnost, kde trávíte nejvíce času, v mnoha případech obývací pokoj nebo kuchyň. Umístěte termostat asi jeden a půl metru nad podlahu, ne na slunce a ne na vnější stěnu.

Co je mrtvé pásmo termostatu?

Pokud má váš termostat mrtvé pásmo, je vaše instalace jakoby „v klidu“. Termostat se zapne pouze tehdy, když se například rozdíl odchyluje o více než 2 °C od nastavené pokojové teploty.

Jaká je ideální pokojová teplota?

Většina lidí zjistí, že ideální pokojová teplota je mezi 19 a 22 stupni Celsia.

Je manuál k Honeywell RTH230B k dispozici v Čeština?

Bohužel nemáme manuál k Honeywell RTH230B k dispozici v Čeština. Tento manuál je k dispozici v Angličtina.

Není vaše otázka uvedena v seznamu? Zeptejte se zde

Žádné výsledky